(fdutils.info)Acronyms
Appendix A Acronyms
*******************
_SD (Single density)_
Single density disks use a data transfer rate of 125 kb/s and are
no longer in use today, because of their low capacity.
_DD (Double density)_
Double density disks normally hold 360KB (5 1/4) or 720KB (3 1/2)
of data per disk.
Double density disks have only a hole on one side (for write
protection).
Double density uses a data transfer rate of 250 kb/s or 300 kb/s
depending on the drive type: 5 1/4 high density drives use 300 kb/s
when writing to a double density diskm 250 kb/s is used in all
other circumstances. The reason why double density disks in high
density drives need a higher data transfer rate is because these
drives rotate faster (360 rpm instead of 300 rpm).
_HD (High density)_
High density disks normally hold 1200KB (5 1/4) or 1440KB (3 1/2)
of data per disk. High density 3 1/2 disks are marked as such by
the presence of a second square hole, just opposed to the write
protect hole. 3 1/2 high density disks are the most commonly used
type of disks today.
_QD (Quad density)_
Quad density is a hybrid between double and high density. It only
exists for 5 1/4 disks, and holds 720KB of data. It can be
obtained by formatting DD disks in a HD drive. QD uses double
density for the density along the tracks (data transfer rate), and
high density for the density perpendicular to the tracks (spacing
between tracks, and thus number of tracks). This came to existence
because these two aspects are limited by two different factors: the
density along the track is limited by the quality of the media,
whereas the density perpendicular to the tracks is mainly limited
by the drive mechanism (this density, expressed in bits per inch
comes nowhere near the limits of the media, even with HD). Thus
quad density is an easy way to double the capacity of an ordinary
double density disk, just by formatting it in a HD drive.
_ED (Extra density)_
Extra density refers to a disk density that can normally hold
2880KB of data per disk. Extra density disks only exist as 3 1/2
disks. ED disks are marked with a second squared hole opposed to
the square hole, which is a little bit closer to the middle of the
edge than that of HD disks. This format never really took off,
because it only was released when storage media with a much higher
capacity, such as CD-Roms, tapes and Zip disks became popular.
ED uses a data transfer rate of 250 kb/s.
_DS (Double sided)_
Self explanatory.
_SS (Single sided)_
Self explanatory
_MSS (Mixed size sectors)_
Mixed sector size formats are formats which use sectors of several
different sizes on a single track. Note: Mixed size sectors, for
details.
_2M (2 Megabytes)_
2M is a high capacity format developed by Ciriaco de Celis. The
basic principle is the same as MSS: mix sectors of several sizes on
a same track, in order to minimize both slack space and header
overhead. 2M is different from MSS in that it uses a normal 18
sector format on its first track. Note: 2M, for details.
_rpm (Rotations per minute)_
All 3 1/2 drives and 5 1/4 DD drives run at 300 rotations per
minute, whereas 5 1/4 HD drives run at 360 rotations per minute.
_rps (Rotations per second)_
See above.
_tpi (tracks per inch)_
Expresses how close cylinders are to each other. Usually, 5 1/4
double density disks have 48 tpi, whereas 5 1/4 high density and
quad density disks have 96 tpi. 3 1/2 disks use 135.5 tpi.
_XDF (eXtended Density Format)_
XDF is a disk format used for the OS/2 distribution disks. Its
operating systems are similar to 2M and MSS disk, but it is faster
due to a more creative arrangement of sectors. Note: XDF, for
details.
_XXDF (eXtended XDF)_
XXDF is an Linux enhancement for XDF. It can store 1992 KB of data
on an ED disk instead of just 1840 available with the regular XDF
format. Note: XXDF, for details.
_MFM (Multi Frequency Modulation)_
MFM is a low level encoding of disk data. It is used for DD, HD
and ED disks, i.e. virtually all disks that are available today.
The PC hardware can only read MFM and FM disks. The doc at:
http://www.moria.de/~michael/floppy/floppy.ps
contains more detailed information about FM and MFM encoding.
_FM (Frequency modulation)_
FM is a low level encoding of disk data. It was used for SD disks,
and is now considered to be obsolete. The doc at:
http://www.moria.de/~michael/floppy/floppy.ps
contains more detailed information about FM and MFM encoding.
_kb (kilobit)_
1000 bits
_kb/s (kilobit per second)_
We express the raw data throughput to and from the disk in this
unit, which is also used in the documentation of the floppy disk
controller.
_B_
Byte. A byte is 8 bits, and is the smallest individually
addressable unit of data.
_KB (K-Byte)_
1024 bytes. Sometimes also noted K.
_KB/s (K-Byte)_
We express the usable data throughput to and from the disk in KB/s.
Roughly, 1 KB/s = 8 kb/s. However, the usable data throughput is
always lower than the raw throughput due to header overhead,
interleaving and seek overhead.
_MB (Megabyte)_
Initially, 1 megabyte was 1024*1024 bytes (i.e. 1048576 bytes).
However, when talking of floppy disk capacity, we understand it as
1000KB, that is 1000*1024 bytes, i.e. 1024000 bytes.
_MB/s (million bytes per second)_
We express (high) raw data throughput to and from the disk in kb/s,
which is also used in the documentation of the floppy disk
controller.
automatically generated by info2www version 1.2.2.9